Engineering Mechanics, part 3 (курсова робота)

Major: Materials Science
Code of subject: 6.132.03.O.026
Credits: 2.00
Department: Department of Technical Mechanics and Engineering Graphics
Lecturer: Predko Rostyslav
Semester: 4 семестр
Mode of study: денна
Learning outcomes: In the discipline "Technical Mechanics" the theory of work, calculations, typical designs, general questions of designing of details of cars and assembly units of general purpose are studied. Calculations of parts are performed according to the criteria of operability to ensure the reliability and durability of parts and machines. At calculations and designing of details of cars acquaintance with standards, questions of unification of details and modern tendencies of development of cars is provided. The purpose of teaching the course is to give students knowledge of the calculation and basics of designing general purpose parts and to facilitate the study of special computational disciplines. As a result of the course work, the student must be able to independently formulate and solve engineering problems, based on a rational choice of calculation and technological schemes that take into account the latest advances in scientific and technological progress.
Required prior and related subjects: 1. Higher mathematics. 2. Physics. 3. Descriptive geometry and graphics. 4. Theoretical mechanics. 5. Resistance of materials. 6. Materials science.
Summary of the subject: 1. Tasks. 2. Selection of the engine and loading parameters of transfers. 3. Calculation of gears for strength. 4. Efforts in gearing and loading on shafts. 5. Design calculation of shafts. 6. Selection and calculation of bearings. 7. Verification calculation of dowels. 8. Determining the size of the main parts of the gearbox. 9. Lubrication and sealing. 10. Calculation and design of the coupling. 11. References. Graphic part Ark.№1 Reducer. Assembly drawing. Format A1 Ark.№2 Reducer. Detailing. The shaft is slow. Assembly drawing. A3 format The shaft is low-speed. Drawing of a shaft. A3 format The shaft is slow. Drawings of a gear wheel. A3 format. Drawings of the coupling. Assembly drawing. A3 format.
Assessment methods and criteria: Semester grade 100 points: current control (timeliness) 10 points - sheet №1 10 points - sheet №2 10 points - explanatory and settlement note 10 points. Work defense 60 points: - quality of execution of 10 points - oral component 50 points
Recommended books: Література до курсової роботи: 1. Булгаков В.М., Черниш О.М., Яременко В.В. Технічна механіка: навчальний посібник. Ніжин: ТЩВ «Видавництво «Аспект – Поліграф», 2013. 2. Курмаз Л.В. Основи конструювання деталей машин. – Харків: Підручник НТУ “ХПІ”, 2010. – 532 с. 3. Павлище В.Т. Основи конструювання та розрахунок деталей машин. Львів, Афіша, 2003, - 557 с. 4. Малащенко В.О., Янків В.В. Деталі машин. Курсове проектування. Львів. Новий світ – 2000, 2004, - 236 с.; 2006, - 252 с.; 2007, - 252 с. 5. Малащенко В.О., Павлище В.Т. Деталі машин. Збірник завдань та прикладів розрахунків. Львів, 1999, 117 с. 6. Малащенко В.О. Муфти приводів. – Львів: НУЛП, 2009. – 216 с. 7. Павлище В.Т., Данило Я.Я. Різьби, різьбові з’єднання та кріпильні деталі: Довідник. – Львів: Інтелект-Захід, 2001. – 239 с. 8. Павлище В.Т. Підшипники кочення. – Львів: Інтелект-Захід, 2001. – 148 с.

Engineering Mechanics, part 3

Major: Materials Science
Code of subject: 6.132.00.O.025
Credits: 4.00
Department: Department of Technical Mechanics and Engineering Graphics
Semester: 4 семестр
Mode of study: денна